The Uptime Variable Nobody Puts in the RFP: Spare Parts

Shared by |

Camber Team

Published |

Topics |

Article

The bus is ready. What if your charger isn’t?

It’s 5:15 a.m. at the depot. The bus passed its pre-trip inspection, the operator is on the clock, and pull-out is 40 minutes away. But the charger it depends on faulted overnight, and the part that fixes it is sitting in a warehouse two states away.

That bus isn’t going anywhere. Neither is the schedule built around it.

Fleets in transit, K-12, and commercial and port operations spend months specifying buses, chargers, software, and grid upgrades. Far less attention goes to a simpler question: when a charger component fails, how fast can the replacement part reach a technician’s hands? That answer often decides whether a charger is down for hours or for weeks.

Charger downtime is a fleet availability problem

A diesel bus can fuel almost anywhere. An electric bus needs its charger, on schedule, every day. When the charger goes down, a mechanically healthy vehicle becomes a spare at best and a missed route at worst.

Fleet operations leave little room to absorb that. Transit agencies plan around fixed pull-out times. School districts plan around bell schedules. Port and commercial fleets plan around shift windows and delivery commitments.

Early adopters learned this firsthand. In California’s utility-run transportation electrification pilots, evaluators found that redundancy mattered in high-use operations, with older chargers pressed back into service when newer ones went down 1. And the World Resources Institute’s Electric School Bus Initiative advocates a single point of contact for charger operation and repair, so district staff aren’t left troubleshooting charger failures themselves 2.

Redundancy and a single accountable partner both help. Neither fixes a charger that’s waiting on a part.

Parts, not repairs, decide how long a charger stays down

Most operators assume repair time depends on technicians: how many there are and how fast they arrive. The data points somewhere else.

ChargerHelp, a California-based charger maintenance company, analyzed more than 500 million charge sessions across 60-plus charging systems 3. Its findings:

  • The delay comes before the repair. In a sample of 47 outage cases, parts and access coordination accounted for 92% of the delay 3. The fix itself was rarely the slow part.
  • Repeat visits drive most downtime. Outages needing more than one technician visit made up 36% of outages but 48% of total downtime days 3. A technician who arrives without the right part has to come back.
  • Those outages last twice as long. Multi-visit repairs took 39 days on average, compared with 18 days for single-visit issues 3.
  • The installed base is aging. 37.6% of U.S. charging ports are now more than three years old 3, which means parts demand will only grow.

This research covers public charging networks, but fleet depots face the same dynamics, often with less margin. Consider the math behind a common reliability benchmark: 97% uptime allows a charger to be down no more than 3% of the year, or about 11 days in total 4. A single part shipped from out of state can use up most of that.

The repair specialists who perform best already know this. The National Renewable Energy Laboratory found that many charger repair companies have built warehouse stocks of replacement parts specifically to cut response times 5.

What does your depot readiness look like?

What good looks like: a parts-readiness framework

Parts readiness isn’t a warehouse shelf. It’s a set of decisions made before the first charger is energized. Fleets that get it right build these six elements into their plans and contracts:

  1. A clear benchmark. Federal NEVI rules require publicly funded chargers to be fully operational more than 97% of the time on average, annually 7. Fleet depots aren’t bound by that rule, but it’s a useful reference point when setting your own targets.
  2. A defined critical spares list. Identify the components most likely to fail or hardest to source, such as power modules, contactors, cables and connectors, and pantograph contact components. Agree on quantities up front.
  3. Local or regional stocking. Know exactly where your parts sit and how long they take to reach your depot. Hours is a different outcome than days.
  4. Field-swappable design. Modular hardware lets a technician replace a failed component on site instead of waiting on a full unit.
  5. Supplier continuity protections. Charging hardware should outlast many supplier relationships. Require a committed parts-availability term, favor non-proprietary components where possible, and ask what happens to support if the hardware maker leaves the market.
  6. Uptime commitments tied to parts. An uptime guarantee means little if the parts plan behind it is vague. Tie availability targets and response times to specific stocking commitments.

Eight questions to ask before you sign

Whether you’re writing an RFP or renewing a service agreement, these questions separate a real parts plan from a promise:

  1. Which components do you consider critical spares for this equipment, and how many will you stock for our sites?
  2. Where are those parts physically stored, and what’s the typical time to reach our depot?
  3. Which components are proprietary to a single manufacturer?
  4. How many years do you commit to parts availability for this hardware?
  5. What happens to parts and support if the hardware manufacturer exits the market?
  6. What share of your repairs are completed in a single technician visit?
  7. How are your uptime and response-time commitments tied to parts availability?
  8. Can you share restoration-time data from existing customers with fleets like ours?

Make parts part of the plan

Chargers will fail. Every piece of equipment does. What separates a two-hour fix from a three-week outage is whether the right part is close by when it happens.

If you’re planning a new deployment or reviewing an existing service agreement, start with the eight questions above or talk to Camber about a parts and uptime review for your fleet.

Talk with the transit team

Sources

  1. California Public Utilities Commission, SB 350 Transportation Electrification Priority Review Projects Final Evaluation
  2. School Transportation News, Bandwidth Can Play Critical Role at School Bus Charging Infrastructure Locations (quoting the World Resources Institute)
  3. Kelley Blue Book, Study Finds Repair Delays Prolong EV Charger Outages, September 18, 2026 (reporting ChargerHelp data)
  4. Canary Media, What’s behind the epidemic of unreliable EV chargers?
  5. National Renewable Energy Laboratory, Impact of Electric Vehicle Charging Station Reliability, Resilience, and Location on Electric Vehicle Adoption, NREL/TP-5R00-89896, August 2024
  6. U.S. Department of Energy, Alternative Fuels Data Center, Massachusetts electric school bus case study
  7. PennDOT, EVC-RAA Funding Opportunity Important Considerations, citing 23 CFR 680.116(b)

Recent News

Article

Pantograph charging is one of the biggest decisions a transit agency makes when it electrifies a bus fleet. It affects depot layout, capital budgets, labor, and how fast buses get back into service. It ...
Read More

Article, Interview

Most fleet electrification planning focuses on vehicles, funding, and power capacity. Far less attention goes to what happens after the chargers are energized, which is where reliability is actually won or lost.  To capture ...
Read More